机器硬件
00:00.0 Host bridge: Intel Corporation Atom Processor Z36xxx/Z37xxx Series SoC Transaction Register (rev 11)
00:02.0 VGA compatible controller: Intel Corporation Atom Processor Z36xxx/Z37xxx Series Graphics & Display (rev 11) 显卡
00:13.0 SATA controller: Intel Corporation Atom Processor E3800 Series SATA AHCI Controller (rev 11) 硬盘
00:14.0 USB controller: Intel Corporation Atom Processor Z36xxx/Z37xxx, Celeron N2000 Series USB xHCI (rev 11) USB
00:1a.0 Encryption controller: Intel Corporation Atom Processor Z36xxx/Z37xxx Series Trusted Execution Engine (rev 11)  
00:1b.0 Audio device: Intel Corporation Atom Processor Z36xxx/Z37xxx Series High Definition Audio Controller (rev 11) 声卡
00:1c.0 PCI bridge: Intel Corporation Atom Processor E3800 Series PCI Express Root Port 1 (rev 11)  硬盘
00:1c.1 PCI bridge: Intel Corporation Atom Processor E3800 Series PCI Express Root Port 2 (rev 11) 硬盘
00:1c.2 PCI bridge: Intel Corporation Atom Processor E3800 Series PCI Express Root Port 3 (rev 11) 硬盘
00:1c.3 PCI bridge: Intel Corporation Atom Processor E3800 Series PCI Express Root Port 4 (rev 11 )硬盘
00:1f.0 ISA bridge: Intel Corporation Atom Processor Z36xxx/Z37xxx Series Power Control Unit (rev 11) isa桥
00:1f.3 SMBus: Intel Corporation Atom Processor E3800 Series SMBus Controller (rev 11)
01:00.0 Ethernet controller: Intel Corporation 82583V Gigabit Network Connection 网卡
03:00.0 SATA controller: Marvell Technology Group Ltd. Device 9215 (rev 11)  硬盘
04:00.0 Ethernet controller: Intel Corporation 82583V Gigabit Network Connection 网卡

想用机器的Mstat -SSD做启动盘

[System Enclosure]
VENDOR = QNAP
MODEL = TS-453B
CAP=0x16149b9c
MAX_DISK_NUM = 4
MAX_FAN_NUM = 1
MAX_TEMP_NUM = 2
INTERNAL_NET_PORT_NUM = 1
MAX_PCIE_SLOT = 1
CPU_TEMP_UNIT = DTS:4
SYSTEM_TEMP_UNIT=EC
SIO_DEVICE = IT8528
PWR_RECOVERY_UNIT = EC
BOARD_SN_DEVICE = VPD:BP
ETH_MAC_DEVICE = NET
DISK_DRV_TYPE = ATA
DISK_DEFAULT_MAX_LINK_SPEED = PD_SATA_SAS_6G
SYSTEM_DISK_CACHEABLE_BITMAP = 0x6
SS_MAX_CHANNELS = 40
SS_FREE_CHANNELS = 4
EUP_STATUS = EC
[System FAN]
FAN_UNIT = EC
FAN_1=I1
FAN_LEVEL_0 = 0
FAN_LEVEL_1 = 70
FAN_LEVEL_2 = 90
FAN_LEVEL_3 = 110
FAN_LEVEL_4 = 130
FAN_LEVEL_5 = 150
FAN_LEVEL_6 = 200
FAN_LEVEL_7 = 250
HEAT_SOURCE = SYS, CPU, DISK
[System I2C]
DEV_BUS = B0031:F1
DEV_PORT = 0
[System EDID 1]
DEV_BUS = B0002:F0
DEV_PORT = 0
[System IO]
RESET_BUTTON = EC
USB_COPY_BUTTON = EC
STATUS_GREEN_LED = EC
STATUS_RED_LED = EC
VPD_MB = EC
VPD_BP = EC
FRONT_USB_LED = EC
LED_BV_INTERFACE = EC
LED_BV_CTRL = PWM
EDID_COUNT=1
VOICE_ALERT_SUPPORT = 0

[System Disk 1]
DEV_BUS=B0028:F0
DEV_PORT = 0
PRESENT_LED = EC
BLINK_LED = EC
ERR_LED = EC
LOCATE_LED = EC

[System Disk 2]
DEV_BUS=B0028:F1
DEV_PORT = 1
PRESENT_LED = EC
BLINK_LED = EC
ERR_LED = EC
LOCATE_LED = EC

[System Disk 3]
DEV_BUS=B0028:F2
DEV_PORT = 2
PRESENT_LED = EC
BLINK_LED = EC
ERR_LED = EC
LOCATE_LED = EC

[System Disk 4]
DEV_BUS=B0028:F3
DEV_PORT = 3
PRESENT_LED = EC
BLINK_LED = EC
ERR_LED = EC
LOCATE_LED = EC

[System Network 1]
DEV_BUS = B0100:F0
DEV_PORT = 0

[System Network 2]
DEV_BUS = B0400:F0
DEV_PORT = 0

[Usb Enclosure]
VENDOR = QNAP
MODEL = USB
MAX_PORT_NUM = 7
EXT_PORT_NUM = 2
USB3_PORT_BITMAP = 0xFE

[Usb Port 1]
DEV_BUS = B0020:F0
DEV_PORT = 1

[Usb Port 2]
DEV_BUS = B0020:F0
DEV_PORT = 3

[Usb Port 3]
DEV_BUS = B00:D20:F0
DEV_PORT = 4

[Usb Port 4]
DEV_BUS = B00:D20:F0
DEV_PORT_SSP = 1
DEV_PORT_SS = 3
DEV_PORT_NS = 2

[Usb Port 5]
DEV_BUS = B00:D20:F0
DEV_PORT_SSP = 1
DEV_PORT_SS = 2
DEV_PORT_NS = 2

[Usb Port 6]
DEV_BUS = B00:D20:F0
DEV_PORT_SSP = 1
DEV_PORT_SS = 1
DEV_PORT_NS = 2

[Usb Port 7]
DEV_BUS = B00:D20:F0
DEV_PORT_SSP = 1
DEV_PORT_SS = 4
DEV_PORT_NS = 2

[Boot Enclosure]
VENDOR = QNAP
MODEL = BOOT
MAX_DISK_NUM = 1

[Boot Disk 1]
DISK_DRV_TYPE = ATA
DEV_BUS = B00:D20:F0
DEV_PORT = 0

[System Memory]
MAX_CHANNEL_NUM = 2
MAX_SLOT_NUM = 2
SLOT1_ADDR = 1, 0x50
SLOT2_ADDR = 2, 0x52

DEV_BUS = B0020:F0启动盘这个是M2接口的？还是介意你做成sata接口的

lucky911game 发表于 2021-3-24 10:34
DEV_BUS = B0020:F0启动盘这个是M2接口的？还是介意你做成sata接口的

如果用U盘启动应该怎么写

盛红茶瓶子 发表于 2021-3-24 11:03
如果用U盘启动应该怎么写

U盘没有实际试验过，sata接口的倒是有成功的；可以参考别人的写法，只能反复实验了才行

mSATA接口应该是B00D19F0