| 已设置、更新好，现在正在走全面测试中。 |
|
用方法2一次成功； 感觉难度主要在拆壳子上，分析如何拆装，然后最后一步还弄两遍（导光棒掉了一次） |
wjq998 发表于 2018-9-19 09:16 就是娘的复杂的要死,要先装linux系统再在系统里安装主机的系统,我现在直接用3T的镜像写入硬盘,再扩容到4t完美 |
| 各位帮忙看看 |
|
root@sysresccd /root % fdisk -l Disk /dev/loop0: 317.1 MiB, 332468224 bytes, 649352 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk /dev/sda: 20 GiB, 21474836480 bytes, 41943040 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: gpt Disk identifier: F24FCD0C-734A-4E32-8E5F-A3C379507358 Device Start End Sectors Size Type /dev/sda1 1032192 5031935 3999744 1.9G Linux RAID /dev/sda2 5031936 9031679 3999744 1.9G Linux RAID /dev/sda3 30720 1032191 1001472 489M Linux filesystem /dev/sda4 9031680 41940991 32909312 15.7G Linux filesystem Partition table entries are not in disk order. Disk /dev/sdb: 3.7 TiB, 4000787030016 bytes, 7814037168 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disklabel type: gpt Disk identifier: B795E8FF-31A8-4F11-A34C-6E1B9B1D43FA Disk /dev/sdc: 7.5 GiB, 8002732032 bytes, 15630336 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0x6f20736b Device Boot Start End Sectors Size Id Type /dev/sdc1 ? 778135908 1919645538 1141509631 544.3G 72 unknown /dev/sdc2 ? 168689522 2104717761 1936028240 923.2G 65 Novell Netware 386 /dev/sdc3 ? 1869881465 3805909656 1936028192 923.2G 79 unknown /dev/sdc4 ? 2885681152 2885736650 55499 27.1M d unknown Partition table entries are not in disk order. root@sysresccd /root % mkdir /mnt/usb root@sysresccd /root % mount -t vfat /dev/sdc /mnt/usb root@sysresccd /root % cd /mnt/usb root@sysresccd /mnt/usb % mdadm -S /dev/md0 mdadm: stopped /dev/md0 root@sysresccd /mnt/usb % ./debrick.sh rootfs.img /dev/sdb destroy ********************** DISK ********************** script will use the following disk: Model: ST4000VX 000-1F4168 (scsi) Disk /dev/sdb: 4001GB Sector size (logical/physical): 512B/4096B Partition Table: gpt Disk Flags: Number Start End Size File system Name Flags is this REALLY the disk you want? [y] y ********************** IMAGE ********************** ********************** IMPLEMENTATION ********************** everything is now prepared! device: /dev/sdb image_img: rootfs.img destroy: true this is the point of no return, continue? [y] y dd: error writing ‘/dev/sdb1’: No space left on device 10+0 records in 9+0 records out 10395648 bytes (10 MB) copied, 0.231762 s, 44.9 MB/s dd: error writing ‘/dev/sdb2’: No space left on device 1+0 records in 0+0 records out 0 bytes (0 B) copied, 0.00339713 s, 0.0 kB/s dd: error writing ‘/dev/sdb3’: No space left on device 1+0 records in 0+0 records out 0 bytes (0 B) copied, 0.0029964 s, 0.0 kB/s dd: error writing ‘/dev/sdb4’: No space left on device 1+0 records in 0+0 records out 0 bytes (0 B) copied, 0.00727841 s, 0.0 kB/s Testing with pattern 0x00: done Reading and comparing: done GNU Parted 3.2 Using /dev/sdb Welcome to GNU Parted! Type 'help' to view a list of commands. (parted) mklabel gpt (parted) mkpart primary 528M 2576M (parted) mkpart primary 2576M 4624M (parted) mkpart primary 16M 528M (parted) mkpart primary 4624M -1M (parted) set 1 raid on (parted) set 2 raid on (parted) quit Information: You may need to update /etc/fstab. Warning: blocksize 65536 not usable on most systems. mke2fs 1.42.12 (29-Aug-2014) mkfs.ext4: Device size reported to be zero. Invalid partition specified, or partition table wasn't reread after running fdisk, due to a modified partition being busy and in use. You may need to reboot to re-read your partition table. destroying was done, would you like to continue with installation? [y] y mdadm: /dev/sdb1 is not a block device mdadm: Cannot find /dev/md0: No such file or directory mke2fs 1.42.12 (29-Aug-2014) The file /dev/md0 does not exist and no size was specified. mdadm: error opening /dev/md0: No such file or directory synchronize raid... mdadm: Cannot find /dev/md0: No such file or directory done copying image to disk... dd: writing to ‘/dev/md0’: No space left on device 1+0 records in 0+0 records out 0 bytes (0 B) copied, 0.00578766 s, 0.0 kB/s mount: /dev/md0 is not a block device (maybe try `-o loop'?) cp: cannot stat ‘/mnt/md0/usr/local/share/bootmd0.scr’: No such file or directory ./debrick.sh: line 359: /mnt/md0/etc/nas/service_startup/ssh: No such file or directory umount: /mnt/md0: not mounted mdadm: /dev/md0 does not appear to be an md device BLKGETSIZE: Inappropriate ioctl for device BLKGETSIZE: Inappropriate ioctl for device all done! device should be debricked! root@sysresccd /mnt/usb % |
|
root@sysresccd /root % fdisk -l Disk /dev/loop0: 317.1 MiB, 332468224 bytes, 649352 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk /dev/sda: 20 GiB, 21474836480 bytes, 41943040 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: gpt Disk identifier: F24FCD0C-734A-4E32-8E5F-A3C379507358 Device Start End Sectors Size Type /dev/sda1 1032192 5031935 3999744 1.9G Linux RAID /dev/sda2 5031936 9031679 3999744 1.9G Linux RAID /dev/sda3 30720 1032191 1001472 489M Linux filesystem /dev/sda4 9031680 41940991 32909312 15.7G Linux filesystem Partition table entries are not in disk order. Disk /dev/sdb: 3.7 TiB, 4000787030016 bytes, 7814037168 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disklabel type: gpt Disk identifier: B795E8FF-31A8-4F11-A34C-6E1B9B1D43FA Disk /dev/sdc: 7.5 GiB, 8002732032 bytes, 15630336 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0x6f20736b Device Boot Start End Sectors Size Id Type /dev/sdc1 ? 778135908 1919645538 1141509631 544.3G 72 unknown /dev/sdc2 ? 168689522 2104717761 1936028240 923.2G 65 Novell Netware 386 /dev/sdc3 ? 1869881465 3805909656 1936028192 923.2G 79 unknown /dev/sdc4 ? 2885681152 2885736650 55499 27.1M d unknown Partition table entries are not in disk order. root@sysresccd /root % mkdir /mnt/usb root@sysresccd /root % mount -t vfat /dev/sdc /mnt/usb root@sysresccd /root % cd /mnt/usb root@sysresccd /mnt/usb % mdadm -S /dev/md0 mdadm: stopped /dev/md0 root@sysresccd /mnt/usb % ./debrick.sh rootfs.img /dev/sdb destroy ********************** DISK ********************** script will use the following disk: Model: ST4000VX 000-1F4168 (scsi) Disk /dev/sdb: 4001GB Sector size (logical/physical): 512B/4096B Partition Table: gpt Disk Flags: Number Start End Size File system Name Flags is this REALLY the disk you want? [y] y ********************** IMAGE ********************** ********************** IMPLEMENTATION ********************** everything is now prepared! device: /dev/sdb image_img: rootfs.img destroy: true this is the point of no return, continue? [y] y dd: error writing ‘/dev/sdb1’: No space left on device 10+0 records in 9+0 records out 10395648 bytes (10 MB) copied, 0.231762 s, 44.9 MB/s dd: error writing ‘/dev/sdb2’: No space left on device 1+0 records in 0+0 records out 0 bytes (0 B) copied, 0.00339713 s, 0.0 kB/s dd: error writing ‘/dev/sdb3’: No space left on device 1+0 records in 0+0 records out 0 bytes (0 B) copied, 0.0029964 s, 0.0 kB/s dd: error writing ‘/dev/sdb4’: No space left on device 1+0 records in 0+0 records out 0 bytes (0 B) copied, 0.00727841 s, 0.0 kB/s Testing with pattern 0x00: done Reading and comparing: done GNU Parted 3.2 Using /dev/sdb Welcome to GNU Parted! Type 'help' to view a list of commands. (parted) mklabel gpt (parted) mkpart primary 528M 2576M (parted) mkpart primary 2576M 4624M (parted) mkpart primary 16M 528M (parted) mkpart primary 4624M -1M (parted) set 1 raid on (parted) set 2 raid on (parted) quit Information: You may need to update /etc/fstab. Warning: blocksize 65536 not usable on most systems. mke2fs 1.42.12 (29-Aug-2014) mkfs.ext4: Device size reported to be zero. Invalid partition specified, or partition table wasn't reread after running fdisk, due to a modified partition being busy and in use. You may need to reboot to re-read your partition table. destroying was done, would you like to continue with installation? [y] y mdadm: /dev/sdb1 is not a block device mdadm: Cannot find /dev/md0: No such file or directory mke2fs 1.42.12 (29-Aug-2014) The file /dev/md0 does not exist and no size was specified. mdadm: error opening /dev/md0: No such file or directory synchronize raid... mdadm: Cannot find /dev/md0: No such file or directory done copying image to disk... dd: writing to ‘/dev/md0’: No space left on device 1+0 records in 0+0 records out 0 bytes (0 B) copied, 0.00578766 s, 0.0 kB/s mount: /dev/md0 is not a block device (maybe try `-o loop'?) cp: cannot stat ‘/mnt/md0/usr/local/share/bootmd0.scr’: No such file or directory ./debrick.sh: line 359: /mnt/md0/etc/nas/service_startup/ssh: No such file or directory umount: /mnt/md0: not mounted mdadm: /dev/md0 does not appear to be an md device BLKGETSIZE: Inappropriate ioctl for device BLKGETSIZE: Inappropriate ioctl for device all done! device should be debricked! root@sysresccd /mnt/usb % |
|
root@sysresccd /root % fdisk -l Disk /dev/loop0: 317.1 MiB, 332468224 bytes, 649352 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk /dev/sda: 20 GiB, 21474836480 bytes, 41943040 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: gpt Disk identifier: F24FCD0C-734A-4E32-8E5F-A3C379507358 Device Start End Sectors Size Type /dev/sda1 1032192 5031935 3999744 1.9G Linux RAID /dev/sda2 5031936 9031679 3999744 1.9G Linux RAID /dev/sda3 30720 1032191 1001472 489M Linux filesystem /dev/sda4 9031680 41940991 32909312 15.7G Linux filesystem Partition table entries are not in disk order. Disk /dev/sdb: 3.7 TiB, 4000787030016 bytes, 7814037168 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disklabel type: gpt Disk identifier: B795E8FF-31A8-4F11-A34C-6E1B9B1D43FA Disk /dev/sdc: 7.5 GiB, 8002732032 bytes, 15630336 sectors Units: sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disklabel type: dos Disk identifier: 0x6f20736b Device Boot Start End Sectors Size Id Type /dev/sdc1 ? 778135908 1919645538 1141509631 544.3G 72 unknown /dev/sdc2 ? 168689522 2104717761 1936028240 923.2G 65 Novell Netware 386 /dev/sdc3 ? 1869881465 3805909656 1936028192 923.2G 79 unknown /dev/sdc4 ? 2885681152 2885736650 55499 27.1M d unknown Partition table entries are not in disk order. root@sysresccd /root % mkdir /mnt/usb root@sysresccd /root % mount -t vfat /dev/sdc /mnt/usb root@sysresccd /root % cd /mnt/usb root@sysresccd /mnt/usb % mdadm -S /dev/md0 mdadm: stopped /dev/md0 root@sysresccd /mnt/usb % ./debrick.sh rootfs.img /dev/sdb destroy ********************** DISK ********************** script will use the following disk: Model: ST4000VX 000-1F4168 (scsi) Disk /dev/sdb: 4001GB Sector size (logical/physical): 512B/4096B Partition Table: gpt Disk Flags: Number Start End Size File system Name Flags is this REALLY the disk you want? [y] y ********************** IMAGE ********************** ********************** IMPLEMENTATION ********************** everything is now prepared! device: /dev/sdb image_img: rootfs.img destroy: true this is the point of no return, continue? [y] y dd: error writing ‘/dev/sdb1’: No space left on device 10+0 records in 9+0 records out 10395648 bytes (10 MB) copied, 0.231762 s, 44.9 MB/s dd: error writing ‘/dev/sdb2’: No space left on device 1+0 records in 0+0 records out 0 bytes (0 B) copied, 0.00339713 s, 0.0 kB/s dd: error writing ‘/dev/sdb3’: No space left on device 1+0 records in 0+0 records out 0 bytes (0 B) copied, 0.0029964 s, 0.0 kB/s dd: error writing ‘/dev/sdb4’: No space left on device 1+0 records in 0+0 records out 0 bytes (0 B) copied, 0.00727841 s, 0.0 kB/s Testing with pattern 0x00: done Reading and comparing: done GNU Parted 3.2 Using /dev/sdb Welcome to GNU Parted! Type 'help' to view a list of commands. (parted) mklabel gpt (parted) mkpart primary 528M 2576M (parted) mkpart primary 2576M 4624M (parted) mkpart primary 16M 528M (parted) mkpart primary 4624M -1M (parted) set 1 raid on (parted) set 2 raid on (parted) quit Information: You may need to update /etc/fstab. Warning: blocksize 65536 not usable on most systems. mke2fs 1.42.12 (29-Aug-2014) mkfs.ext4: Device size reported to be zero. Invalid partition specified, or partition table wasn't reread after running fdisk, due to a modified partition being busy and in use. You may need to reboot to re-read your partition table. destroying was done, would you like to continue with installation? [y] y mdadm: /dev/sdb1 is not a block device mdadm: Cannot find /dev/md0: No such file or directory mke2fs 1.42.12 (29-Aug-2014) The file /dev/md0 does not exist and no size was specified. mdadm: error opening /dev/md0: No such file or directory synchronize raid... mdadm: Cannot find /dev/md0: No such file or directory done copying image to disk... dd: writing to ‘/dev/md0’: No space left on device 1+0 records in 0+0 records out 0 bytes (0 B) copied, 0.00578766 s, 0.0 kB/s mount: /dev/md0 is not a block device (maybe try `-o loop'?) cp: cannot stat ‘/mnt/md0/usr/local/share/bootmd0.scr’: No such file or directory ./debrick.sh: line 359: /mnt/md0/etc/nas/service_startup/ssh: No such file or directory umount: /mnt/md0: not mounted mdadm: /dev/md0 does not appear to be an md device BLKGETSIZE: Inappropriate ioctl for device BLKGETSIZE: Inappropriate ioctl for device all done! device should be debricked! root@sysresccd /mnt/usb % |
组图打开中，请稍候......