求助，有没有人搞过东芝这款NAS，Toshiba Canvio Home，配置和威联通qnap hs-210相同，要刷机的话是不是要把闪存换成16M呢？

开机信息如下：
         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
_   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/    |____/ \___/ \___/ \__|  ** LOADER ** ** uboot_ver:v0.0.3 **

** MARVELL BOARD: DB-88F6282A-BP LE

U-Boot 1.1.4 (Feb 26 2013 - 14:41:11) Marvell version: 3.6.0

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CD5A0

Soc: 88F6282 A1 CPU running @ 1600Mhz L2 running @ 533Mhz
SysClock = 533Mhz , TClock = 200Mhz

DRAM (DDR3) CAS Latency = 7 tRP = 7 tRAS = 20 tRCD=7
DRAM CS[0] base 0x00000000   size 256MB
DRAM Total size 256MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Found ADT7473, program PWM1 ... OK
[512kB@f8000000] Flash: 512 kB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
PEX 1: interface detected no Link.
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (6)
  Device 0 @ 0 0:
Model: ST3320620AS                              Firm: 3.AAC    Ser#:             5QF1C3AJ
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 305245.3 MB = 298.0 GB (625142448 x 512)


** Unable to read "/uImage" from ide 0:1 **

** Unable to read "/rootfs_shrink.cramfs.canvio.preroot" from ide 0:1 **
## Booting image at 02000000 ...
Bad Magic Number
** Bad partition 1 **
** Bad partition 1 **
## Booting image at 02000000 ...
Bad Magic Number
(Re)start USB...
USB:   scanning bus for devices... 1 USB Device(s) found
Waiting for storage device(s) to settle before scanning...
0 Storage Device(s) found
** Can't read from device 0 **

** Unable to use usb 0:1 for fatload **
** Can't read from device 0 **

** Unable to use usb 0:1 for fatload **
## Booting image at 02000000 ...
Bad Magic Number
egiga0 no link
Using egiga0 device
TFTP from server 192.168.32.4; our IP address is 192.168.1.2
Filename 'TCC-C2/bootimage/uImage'.
Load address: 0x2000000
Loading: ## Warning: gatewayip needed but not set
## Warning: gatewayip needed but not set
T ## Warning: gatewayip needed but not set
## Warning: gatewayip needed but not set
T ## Warning: gatewayip needed but not set

拆机图片。。。。。。

拆机图片。。。。。。